
An FE error code on an LG front-load washer means the machine detected too much water in the tub. The most likely causes are too much detergent, a clogged drain pump filter, or a blocked hose to the water level sensor, and the fix starts with draining the tub and cleaning those spots. If the washer keeps taking in water after you unplug it, the water inlet valve is stuck open and needs replacing.
Most people assume an FE code means a dead part and start shopping. That’s usually wrong. LG’s Help Library lists detergent, debris and frozen hoses as reasons for FE, so the free checks come first and the parts come last.
This guide covers what the code means, how to tell the six causes apart, and when it’s time to stop and call a technician. It’s written to help you troubleshoot LG front-load models, so if you’ve got a top-loader that words the code differently, your manual has the final say.
Meaning of the FE code on an LG washer
FE is the fill error, and on LG front-loaders it works as the overfill warning. LG’s Help Library says the code appears on the display when the washer overfills with water.
The washer tracks its water level through a pressure sensor. When the reading climbs higher than it should, the washer stops and shows FE. HomeServe’s list of LG codes notes that the drain pump then runs by itself to clear the water.
Don’t mix FE up with its neighbors. That same list puts IE as water not filling, OE as water not draining, and PE as a fault in the pressure sensor itself.
Why does an LG washer show FE?
LG’s Help Library names three causes for an overfilling front-load washer. Debris can block the hose that connects to the water level sensor, a clogged drain pump filter can stop water from draining, and in cold weather the water supply hose or drain hose can freeze. The same page warns that hardened detergent residue in the dispenser can send concentrated detergent into the drum all at once.
Detergent matters more than people expect. Cal Poly’s housing guide to LG front-load codes says FE flags excess water or suds in the tub, so using only the recommended amount is the cheapest fix there is.
If those check out, a part has usually failed. A water inlet valve stuck open keeps feeding the tub, a failing water level pressure switch misreads how full it is, and, least often, the main control board is to blame, according to AppliancePartsPros’ repair guides for LG FE errors. From experience, the smarter move is ruling out the free causes before you spend a cent on parts.
How do you fix an LG washer FE error?

Work through these in order, with the faucets closed and the washer unplugged before you touch anything.
- Turn off both water faucets and unplug the washer.
- Open the service cover at the bottom front and drain the remaining water through the residual water hose. LG warns the water may be hot, so keep towels and a shallow pan ready.
- Clean the drain pump filter, which LG names as a cause. Your manual shows where it sits on your model.
- Check the supply and drain hoses for kinks. In freezing weather, pour warm water, about 120 to 140°F (50 to 60°C), into the drum and close the door to thaw a frozen hose, as LG advises.
- Run a short cycle with only the recommended amount of detergent and watch that the water drains and FE doesn’t return.
If FE comes back, unplug the washer again and inspect the water level hose that runs from the tub to the pressure switch. AppliancePartsPros says to look for cracks, kinks or blockages, and to replace the hose if it’s damaged.
What most people don’t know about FE
A drained tub isn’t proof of a fix. Since the washer drains itself when FE trips, you can open the door to an empty drum and assume the problem passed while a stuck valve quietly refills it. Most people miss this entirely.
The unplug test settles it. With the washer unplugged and both faucets closed, slowly open the cold faucet and watch for water entering the washer. AppliancePartsPros’ guide says water entering at that point means the cold inlet valve is faulty, and you repeat the check with the hot faucet. A healthy valve stays shut without power, so any water getting through points to a valve stuck open. Close the faucets again straight afterward.
When to call a technician
Call a technician if FE returns after you’ve drained the tub, cleaned the drain pump filter and checked the hoses. The same goes if the washer overfills or starts to leak onto the floor, or if the unplug test shows water coming in. Those signs point to the inlet valve, the pressure switch or the control board, and a leaking washer can damage flooring fast.
Keep both faucets closed and the washer unplugged until help arrives. LG’s Help Library says you can request a technician visit if the problem continues after these steps.
Your next step

FE is a warning, not a verdict. Drain the tub, clean the drain pump filter and cut your detergent back to the recommended amount, then run one cycle. If the code returns, do the unplug test before you buy anything.
FAQ: LG washer FE error code
What does FE mean on an LG washer?
FE is the fill error, meaning the washer overfilled with too much water. LG’s Help Library describes it as the overfill code on front-load models.
Can too much detergent cause an FE error on an LG washer?
Yes. LG lists detergent among the reasons for FE, and Cal Poly’s housing guide says the code can flag excess suds. Use only the recommended amount for your LG washing machine.
How do I reset an LG washer after an FE error?
Unplug the washer for a few minutes, plug it back in and run a cycle. A reset only clears the display, not the cause, so FE will return until you fix the underlying problem.
Is the FE error the same as PE on an LG washer?
No. FE signals overfilling, while PE signals a fault in the water level pressure sensor, according to HomeServe’s list of LG codes.









