
A dishwasher not draining usually has a clogged dishwasher filter and sump, a kinked or blocked drain hose, or a backed-up garbage disposal or sink drain at the far end of the line. Those are the first things to check, and none of them needs more than a flashlight, a towel and a screwdriver. A failed drain pump is the less common cause, and I’ll cover how to tell it apart from the simple blockages.
Standing water in dishwasher tubs is gross and alarming, but it’s rarely a sign of a dead machine. In most cases the water is stuck somewhere on the way out, not trapped by a broken part. The path runs from the sump through the drain pump, out the drain hose, and into the disposal inlet or the sink drain, and a clog or kink at any point stops the whole line.
This guide follows that path in the order that finds the cause fastest, using what manufacturer manuals from brands like Bosch, Whirlpool and GE say about filters, drain hoses and pumps. Stop as soon as the water goes down.
Is Water at the Bottom of the Dishwasher Normal?
Some water at the bottom is normal on many models. Dishwashers often keep a small amount in the sump after a cycle, and it’s usually a shallow film, not a pool. Your owner’s manual says how much to expect for your model.
If the water level sits above the filter, covers the lower spray arm or reaches the bottom rack, the dishwasher won’t drain properly and something is blocking the line. Dirty water with a foul smell points the same way. If you see suds, too much detergent or hand dish soap in the tub is the likely cause, and you can bail out the suds and run a rinse before assuming a blockage.
Try a drain cycle or cancel and reset the machine once before you take anything apart, since a cycle interrupted by a power blip can leave water behind. Many models have a cancel or drain button, and the manual lists the exact steps for yours.
Clear the Filter and Sump First
A clogged filter is the most common reason for standing water. Food debris, glass fragments and bits of label pile up on the coarse filter and the fine mesh screen beneath it, and the pile blocks the opening to the drain pump. Switch off the breaker first, then bail out the standing water with a cup and soak up the rest with a towel.
Remove the filter, rinse it, and look into the sump with a flashlight. Pull out anything loose by hand, wearing gloves in case of broken glass. A cherry pit or a scrap of label sitting over the sump opening is enough to hold water in the tub.
From experience, the smarter move is to clean the filter before anything else on the list, since it costs nothing and takes five minutes.
Is the Drain Hose Kinked or Clogged?

The drain hose runs from the drain pump to the disposal or the sink drain. A kink is common after the dishwasher has been pushed back into place, and a clogged hose builds up greasy sludge over the years. Either one stops the water from leaving.
With the breaker off, look under the sink and trace the hose, or pull the dishwasher forward only as far as the connections allow. Straighten any kink. Loosen the hose clamp with pliers or a screwdriver, detach the hose, and check for a clog by running water through it into a bucket. Expect dirty water, so keep towels ready.
Check the high loop too. Most installation guides route the hose up to the underside of the countertop before it drops to the drain, which keeps sink water from siphoning back into the tub. A hose with no loop can let dirty water run back into the machine.
Could the Garbage Disposal or Sink Drain Be the Problem?
Yes, and it’s the place people check last. Most dishwashers drain into the garbage disposal inlet or the kitchen sink drain, so a clogged disposal or sink drain backs up into the tub. If the sink fills slowly or gurgles while the dishwasher runs, that’s your clue. Run the disposal with cold water flowing, keep your hands out of it, and see whether the sink drains freely. If the main sink line is clogged beyond the disposal, a plumber is the right call.
New disposal installs have a second trap. The disposal’s dishwasher inlet comes with a knockout plug in the opening, and if the installer didn’t remove it, the drain hose meets a blocked inlet and water can’t get in. Turn off the disposal’s power and check from the disposal side, following the disposal’s installation instructions to remove the plug and fish out the loose piece.
What Most People Don’t Know About the Air Gap
Some sinks have a small chrome cylinder beside the faucet, called an air gap, and it’s the part most often forgotten. Water from the dishwasher passes through it on the way to the disposal, and it clogs with the same sludge as the drain hose. Local plumbing code decides whether a home has an air gap or a high loop, and your manual shows which setup the dishwasher expects.
If you have one, pop off the cap and clean the inside with a small brush. A clogged air gap can stop the dishwasher from draining and sometimes spits dirty water out of the top.
How Do You Know the Drain Pump Has Failed?
A failing drain pump is less common than a clog, and it’s the diagnosis to reach for last. The drain pump moves water out of the sump and through the drain hose, and there are two usual failures. If the pump is humming but no water moves, something is jammed in the impeller, often a piece of glass, an olive pit or a label that got past the filter.
If the pump stays silent when the dishwasher tries to drain, the pump motor, a wiring connection or the control board may be at fault, and an error code on the display often points to the drain circuit. Some models also use a check valve or a drain solenoid, and a stuck one can hold water in the tub. Your owner’s manual lists the error code meanings and shows where the pump sits behind the lower access panel.
Step-by-Step: Finding the Blockage in Order
- Switch off the breaker, bail out the standing water with a cup, and mop up with a towel.
- Remove the filter, clean it, and clear the sump with a flashlight.
- Check the drain hose for kinks and confirm the high loop is in place.
- Loosen the hose clamp, detach the hose, and flush it for a clog.
- Run the disposal and test the kitchen sink for backing up. Clean the air gap if you have one.
- On a new install, confirm the knockout plug was removed from the disposal inlet.
- Restore power, run a short wash cycle and watch the water level. If it still won’t drain, move to the next section.
When to Call a Technician
If the filter, hose, disposal and air gap all check out and the dishwasher still won’t drain, the drain pump, check valve or control board is the likely fault. Call a technician if the pump hums with no water movement after you’ve cleared the sump, if an error code keeps coming back, or if water leaks while the machine tries to drain. Call a plumber if the sink drain backs up beyond the disposal.
Dishwashers combine water and electricity, so keep the breaker off for every hands-on check. For an older machine, ask for the dishwasher repair quote next to the price of a replacement before you decide.
Dishwasher Not Draining: Common Questions
Why is my dishwasher not draining?
Most often it’s a clogged filter, a kinked or blocked drain hose, or a backed-up disposal or sink drain. Check these before suspecting the drain pump.
Why won’t my dishwasher drain after a new garbage disposal install?
The knockout plug in the disposal’s dishwasher inlet may still be in place. Remove it following the disposal’s installation instructions.
Is standing water in the dishwasher after a cycle normal?
A small amount in the sump can be normal, depending on the model. Water covering the filter or the bottom rack isn’t, so check your owner’s manual.
What does it mean if the dishwasher hums but won’t drain?
Usually something is jammed in the drain pump impeller, such as broken glass, a pit or a label.
What Comes Next

Start with the filter, then follow the water out. The cause almost always sits somewhere between the sump and the sink, and you now know every stop on that path. If the dishwasher still won’t drain once the whole path is clear, you can hand a technician a short list of what you’ve already ruled out.









