
A dishwasher not getting water almost always comes down to one of four things: a closed or kinked supply line, a door latch that isn’t registering, a stuck float, or a failed water inlet valve. If your dishwasher won’t fill, start with the under-sink valve and the door latch, because both take minutes to check and rule out more cases than any part swap ever will.
Here’s the logic behind that order. A dishwasher only opens its water inlet valve when three conditions line up: water is reaching the valve, the control board believes the door is closed, and the float switch says the dishwasher tub isn’t already full. Break any one of them and the fill cycle never begins, so the wash cycle starts, the detergent sits in its dispenser, and the tub stays dry.
I’ll walk through each check in the order that wastes the least time, drawing on manufacturer installation manuals and published repair guides. Unplug the dishwasher or switch off its breaker before touching anything electrical, and shut the water off before you disconnect any hose.
Is Water Actually Reaching the Dishwasher?
Start at the shut-off valve under the kitchen sink and confirm it’s fully open. A valve left partly closed after a sink repair is enough to leave a dishwasher not filling with water, and it’s the one fix that costs nothing. Glance at the control panel too, since a machine set to delay start looks exactly like one that refuses to fill.
Then follow the braided hose from the valve toward the dishwasher. A kinked or crushed line behind the kick panel restricts flow, and it happens most often when the machine was pushed back into its cabinet after cleaning. Run the kitchen faucet on hot as a comparison: weak flow there points to low water pressure in the household water supply, not the appliance. GE’s installation instructions say the hot water line must deliver between 20 and 120 PSI, and Samsung’s DW80R7060 manual gives the same range along with a water heater temperature of 120°F to 149°F.
Why a Door Latch Can Stop the Fill Before It Starts
The door switch is built into the door latch assembly, and the control board won’t open the water inlet valve until that switch reports a closed door. Close the door slowly and listen for a firm click. A rack, a tall utensil or a dish edge poking past the opening can keep the latch from fully engaging without looking wrong.
If the door clearly latches and nothing happens, test the switch. Unplug the machine, remove the latch mounting screws, hold the switch lever down and measure across the pins with a multimeter. Sears Home Services’ GE troubleshooting guidance describes a good switch as showing continuity, near zero ohms, while an infinite reading means the whole latch assembly needs replacing.
This usually goes wrong when people replace the latch before checking the wiring harness. iFixit’s Samsung guide notes a known failure in the door wiring harness that can disable both the door switch and the inlet valve, so inspect the connectors before buying parts.
How a Stuck Float Fakes a Full Tub
The float assembly sits on the floor of the tub, and the float switch beneath it cuts power to the water inlet valve as overfill protection. If the float is stuck in the up position, the board behaves as though the tub is already full and the fill cycle never starts. Sears Home Services notes that a GE dishwasher staying empty through a whole cycle points to a stuck float switch or a blocked inlet valve.
Lift the float by hand. It should rise freely and drop back under its own weight. Debris, label fragments or a sliver of broken glass under the dome are the usual culprits, and cleaning them out fixes the problem more often than replacing the part. If the float moves fine, unplug the dishwasher and test the float switch for continuity with the float down; an open reading means the switch needs replacing. Loose wires at the switch cause the same symptom, so check the connectors while you’re there.
Clearing and Testing the Water Inlet Valve

The water inlet valve is a solenoid-operated valve on the lower left of most dishwashers, behind the kick panel, and Whirlpool and Kenmore installation manuals place the water connection on that left side. Turn off the water, cut power at the breaker, and remove the access panel. Disconnect the supply line over a towel and look into the valve inlet. A small mesh screen sits there, and sediment or mineral deposits from hard water buildup can clog it. Brush it clean under running water or soak it in vinegar, then flush the supply line into a bucket before reconnecting. GE’s installation instructions call for flushing the line to clear debris on new installs, and the same logic applies here.
If the inlet screen is clean, pull the two wires off the solenoid and measure resistance across its terminals. Published readings vary by brand, which is why your service manual or tech sheet matters. Many valves land somewhere between 500 and 1,500 ohms, and some GE valves read higher. An infinite reading means the coil is open and the valve must be replaced; a reading near zero means it’s shorted.
For water inlet valve replacement, match the part by model number and buy an OEM part. A common GE single-solenoid valve carries part number WD15X10003, but confirm yours against the model number before ordering.
What Most People Don’t Know About the Voltage Test
Resistance only tells you whether the coil is intact, not whether the valve actually opens. Parts retailers’ own repair guides admit a valve can pass a continuity test and still need replacing, since the coil can read normal while the valve itself is blocked or stuck. That’s why a dishwasher humming but no water coming in can survive an ohm test and still be a bad valve.
The smarter move is a voltage reading during a live fill. With the access panel off and your hands clear of everything else, start a normal cycle and measure AC voltage across the valve terminals when the fill should begin. About 120 volts with no water entering means the valve or its screen is the problem. No voltage means the valve is innocent, and the fault sits upstream in the door switch, float switch, wiring or control board. That one reading splits the whole diagnosis in half and keeps you from buying a valve you didn’t need. Only attempt it if you’re comfortable working near live terminals.
When Should You Call an Appliance Technician?
Call one when supply, latch and float all check out and either the valve shows voltage but still won’t open after replacement, or voltage never reaches it at all. That pattern points to the control board or a damaged wiring harness, which is diagnostic work worth leaving to a technician with the service manual.
Stop and call for any leak or flooding, scorched connectors, or a machine stuck in drain that throws an error code you can’t clear, since that usually points to the drain hose or pump rather than the fill side. Have the model number and the code ready so the technician arrives with the right part. On an older dishwasher, ask for the repair cost on a board before agreeing, because the repair-or-replace math shifts quickly.
Frequently Asked Questions
Why is my dishwasher humming but not filling with water?
A hum with an empty tub usually means the board is calling for water but the inlet valve is starved of supply, clogged at the screen, or failing. Check the shut-off valve and inlet screen first, then test the valve.
Can a bad door latch stop a dishwasher from filling with water?
Yes. The control board won’t open the inlet valve unless the door switch reports a closed door, so a worn latch or broken switch can leave the tub empty.
Will a reset fix a dishwasher that won’t fill?
Switching the breaker off for a few minutes can clear a confused control board, but a power cycle won’t repair a failed valve, float or latch. If the problem returns, work through the checks above.
What should a dishwasher inlet valve read on a multimeter?
It varies by brand and model, but many solenoids fall between 500 and 1,500 ohms. An infinite reading always means a failed coil, and your model’s tech sheet gives the exact range.
Your Next Step

Do the free checks first: shut-off valve, supply line, door click, float. If all four pass, the voltage test tells you whether to buy a valve or book a technician. Write your model number down before you start, because every part decision depends on it.









