
A dryer that runs but won’t turn the drum most often has a broken drive belt or a worn idler pulley. On a Whirlpool, Kenmore or Maytag dryer, a motor that hums or runs while the drum sits still points to the belt, while a dryer that makes no sound at all points to the door switch, the thermal fuse or the drive motor. Most of these repairs need only a screwdriver, a nut driver and a putty knife.
Here’s what most people get wrong. They assume the motor died and start shopping for a new dryer, when the part that failed is a rubber belt. This usually goes wrong when someone replaces the expensive piece first and never checks the cheap one. I’ll walk you through the checks in the order that saves the most money, so you can diagnose a dryer not spinning before you buy a single replacement part. Unplug the dryer first, and close the gas shutoff valve if yours is a gas dryer.
Why Is My Dryer Not Spinning?
Five parts cause most cases of a dryer that won’t spin: the drive belt, the idler pulley, the drive motor, the door switch and the thermal fuse. The belt wraps around the drum and the motor pulley, so when it snaps the motor keeps running while the drum doesn’t move. The idler pulley holds tension on that belt, and when its wheel wears out the belt slips or jumps off. The other three parts control power to the motor, so when one fails the dryer won’t start or tumble at all.
The fastest way to sort these causes is to listen. A dryer that runs or hums with a still drum is a belt-side problem. A silent dryer is an electrical-side problem. That one observation cuts your troubleshooting in half before you open a single panel.
Manufacturer service manuals tell you to disconnect power before removing any panel, and on a gas dryer you should also close the gas shutoff valve behind the machine. Pull the power cord from the outlet rather than relying on the circuit breaker alone.
How Do I Tell If the Drive Belt Is Broken?

Start with the hand test, because it costs nothing. With the dryer unplugged, open the door and turn the drum by hand. A drum with a healthy belt feels snug and resists you a little, while a drum with a broken belt spins loosely with almost no effort.
- Unplug the dryer from the outlet and, on a gas dryer, close the gas shutoff valve.
- Open the door and turn the drum by hand. A loose, free-spinning drum suggests a broken or slipped belt.
- Find the model number on the label inside the door frame and look up the service manual for how your cabinet opens.
- Remove the top or front panel, using the putty knife to release the clips and the nut driver for hex screws.
- Look at the belt around the drum. A snapped, stretched, frayed or shiny belt needs replacing.
If the belt is visibly broken, you have your answer. The replacement is its own job, and I cover the routing and part matching in a separate walkthrough instead of squeezing it in here. Match the replacement part to your model number, not just the brand, because belts differ between models even from the same maker.
Could a Worn Idler Pulley Be the Problem?
Sometimes the belt looks fine and the drum still won’t turn properly. That points to the idler pulley, the small wheel on a spring-loaded arm that keeps the belt tight. Spin the wheel by hand with the dryer unplugged. It should turn smoothly and quietly, and a wheel that wobbles, drags or feels gritty is worn out.
A weak tension spring causes the same symptom, because the belt loses its grip under a heavy load and the drum stalls. From experience, the smarter move is to replace the pulley and belt together, since a new belt riding on a worn wheel tends to fail again.
Squealing or thumping before the drum stopped is a strong hint that the pulley or the drum rollers were already going. If the dryer was making noise for weeks before it quit, that history matters more than the final failure.
Dead-Silent Dryer: Door Switch, Thermal Fuse or Motor?
When the dryer makes no sound at all, the belt isn’t your problem yet. Power isn’t reaching the motor, or the motor itself has failed. Work through three suspects in order.
The door switch tells the dryer the door is closed. Push the door shut and listen for a click from the latch. No click, or a latch that feels loose, means the door switch or door latch is suspect. With the dryer unplugged, a continuity test with a multimeter shows whether the switch passes current.
The thermal fuse is a safety part that blows when the dryer overheats, often from lint buildup in the vent. On some models a blown fuse cuts power to the motor, so the dryer won’t start. Test it for continuity too. A fuse with no continuity has blown, but find out why it overheated, or the new one will blow as well. That topic has its own article, so I won’t repeat it here.
If the switch and fuse both pass and the dryer only hums when you press start, the drive motor or its start switch is next. Weigh the dryer repair cost against the price of a new unit before buying a motor, especially on an older machine.
What Most People Don’t Know About a Dryer That Won’t Spin
The belt is rarely the root cause. It’s just the part that gave up first. A belt snaps because something made it work harder: worn drum rollers, a seized idler pulley, worn drum glides, or a habit of stuffing the drum with a heavy load of wet clothes.
Slip a new belt onto a dryer with a rough roller or a gritty pulley and the replacement tends to fail again. So while the cabinet is open, spin each drum roller and the idler pulley by hand, and replace any that wobble or grind.
Vacuum the lint out of the motor area at the same time, because buildup there adds heat and drag. It adds a few minutes and a small parts cost, and it’s the difference between a lasting repair and doing the job twice.
When Should I Call a Technician?
Call a technician if you smell gas, smell something burning, or find scorched wiring. Call one too if the circuit breaker trips when the dryer starts, since that points to a motor or wiring fault rather than a worn belt.
If you’re uncomfortable working near a gas line or using a multimeter, stop there. A licensed appliance repair technician can diagnose the problem quickly, and a motor or control repair on an older dryer deserves a quote before you commit.
Your Next Step

Tonight, unplug the dryer and do the hand test. A free-spinning drum means the belt or pulley, while a stiff drum or a silent dryer sends you down the electrical path. Write down your model number before you order anything, because every part you buy depends on it.
Dryer Not Spinning: Common Questions
Why is my dryer running but the drum is not spinning?
A broken or slipped drive belt is the most common cause. The motor still runs, but the belt that connects it to the drum is no longer doing its job.
How do I know if the dryer belt is broken?
Unplug the dryer and turn the drum by hand. If it spins freely with little resistance, the belt is likely broken or off, and you can confirm it by looking at the belt under the panel.
Why does my dryer hum but not turn?
A hum without drum movement means the motor is getting power but can’t turn the load. That points to a seized idler pulley, a jammed drum or a failing drive motor.
Can a thermal fuse stop a dryer from spinning?
Yes, on some models. A blown thermal fuse can cut power to the motor, so the dryer won’t start or tumble until the fuse is replaced and the cause of the overheating is fixed.
Is it worth fixing a dryer that won’t spin?
Usually, when the cause is a belt or pulley, since those are small parts you can often replace yourself. For a failed motor, compare the repair cost with the dryer’s age before deciding.









