
A Samsung washer showing an SE error code has a drain error, and the most likely cause is a clogged drain pump filter or a kinked drain hose. Clean the filter, straighten the hose, and the code usually clears. Samsung’s own support pages list this fault as the 5E code, so everything written about 5E applies to your machine.
Most people assume SE and 5E are two different faults. They aren’t. On many Samsung displays the digit 5 is drawn with the same segments as the letter S, so the washing machine is saying 5E and your eyes are reading SE. What matters is the message underneath: the washer tried to pump water out, the water didn’t leave fast enough, and the control board stopped the cycle.
That’s good news, because a drainage problem is one of the most fixable faults a washer can throw. Below, I’ll cover what the code means, what causes it, five steps that clear it most of the time, and the point where you should stop and call a technician. For the first few checks, all you need is a towel, a shallow pan and some warm water.
What does the SE error code mean on a Samsung washer?
The SE code means your Samsung washer couldn’t drain its water within the time the control board allows. Samsung’s UK support guide to the 5E and 5C codes says the washing machine has detected a drainage issue, and that the most common reasons are a blocked filter or a kinked drain hose. That’s the whole message. It isn’t a motor fault or a leak, at least not to start with.
You’ll usually spot it as a washer that stops mid-cycle with wet clothes and standing water in the drum.
Samsung also notes that the buttons on the washing machine are disabled for three minutes after the code appears. Don’t read an unresponsive panel as a dead one. Give it the three minutes before you try to reset anything.
Is SE the same as 5E, 5C, SC and nd?
For repair purposes, yes. Sears Home Services groups nd, 5E, SE, 5C, SC and 1 5C together as the drain codes on Samsung washers, all shown when the control board detects the machine isn’t draining properly. SE and SC are simply how 5E and 5C look on a segment display, and the nd error code is the no-drain version of the same problem.
Where models differ is the hardware you can reach. A front-load washer keeps its drain pump filter behind a small cover at the bottom front. A top-load washer is built differently, so you’ll lean more on the hose and pump checks below.
What causes a Samsung washer to throw the SE code?
The usual cause is a clogged filter. The debris filter in a front-load washer catches coins, hair ties, lint and whatever else escapes from pockets, and once it packs solid, water can’t reach the drain pump. Samsung’s guidance puts the blocked filter at the top of the list for a reason.
Next comes the drain hose. A kinked or crushed hose stops water just as well as a clog does, and so does a hose pushed so far down the standpipe that it sits in standing water. Hose height matters too, since a hose set too low or too high can slow the flow. Beacon’s Samsung SE guide lists hose placement alongside the packed pump filter for this reason.
A washer that isn’t level can also trigger the code, according to How To Fix It’s Samsung guide, which tells owners to check the adjustable feet along with the filter and pump. The pump itself is the last suspect. A jammed pump impeller or a damaged wiring harness will stop it moving water, but those fail less often than a dirty filter.
From experience, the smarter move is always to work from cheapest to most expensive: hose, filter, level, then pump.
How do you fix a Samsung washer SE error code?

Work through these in order, and unplug the washer before you touch anything inside it. This usually goes wrong when someone skips to the pump and never looks at the hose, which is the quickest check on the list.
- Power cycle the washer. Unplug it, wait a few minutes, plug it back in and run a rinse and spin cycle. Samsung Australia’s 5E guide says the washer should drain at the start of the test cycle, so watch that first minute.
- Check the drain hose. Pull the washer forward gently and straighten any kinks. Make sure the hose isn’t crushed behind the machine and that its end isn’t buried deep in the standpipe or sitting in water.
- Clean the drain pump filter. With the washer unplugged, put a towel and shallow pan under the access panel, since the filter housing holds water. Open the panel, unscrew the filter, and remove the coins, hair ties and lint. Wash the filter in warm water and wipe the recess with a damp cloth. Samsung’s instructions finish by replacing the filter and rotating it clockwise to lock it in place.
- Level the washer. Adjust the feet until the machine sits flat and doesn’t rock, then run another test cycle.
- Inspect the pump. If the filter and hose are clear and the water still won’t leave, look for something stuck in the pump impeller. A damaged pump needs replacing, and that’s where many people stop and book a repair.
What most people don’t know about the SE code
Most people miss this entirely: the SE code doesn’t always mean water is stuck. Whitegoodshelp’s guide to Samsung error 5E explains that it can signal a genuine drain failure, such as a blocked filter or failed pump, or a pressure system fault where the machine drains correctly but the control board never registers it.
That changes how you diagnose it. If the drum is empty when the code appears, and the filter and hose are both clean, the problem may be the water level sensor or the board rather than the pump. Replacing a pump in that situation costs money and fixes nothing.
When should you call a technician?
Call a licensed technician if the code returns after you’ve cleaned the filter, cleared the hose and leveled the machine. The same goes for a pump that stays silent when it should be running, a damaged wiring harness, or any sign of water near electrical parts. Samsung’s support guide tells owners to contact Samsung Support when the issue persists after the listed steps, and that’s also the route to take if the washer is still under warranty.
Always unplug the washer before you diagnose anything. Water and mains power don’t mix, and a quick shock risk isn’t worth saving a service fee.
Your Next Step

Start with the hose and the drain pump filter tonight, before you spend a cent on parts. That pair clears the SE code more often than anything else, and both checks take only a towel and a few minutes. Once it’s running again, check the filter every few months, especially if your family leaves things in pockets.
Frequently asked questions
What does SE mean on a Samsung washer?
SE is how the 5E drain error appears on many segment displays. It means the washer couldn’t drain its water within the allowed time.
Can I just reset the Samsung washer to clear SE?
A power cycle can clear the display, but the code returns if the cause is still there. Fix the filter, hose or level first.
Is the Samsung nd error the same as SE?
Close. The nd error code is the no-drain version of the same drain problem, and the same checks apply.
Do top-load Samsung washers have a pump filter?
Not one you can reach the same way as a front-load washer’s, so start with the hose and level checks, then book a repair if the code stays.









